Aetna -133 butyl waterproof caulking sealant steel doors and sealants details Aetna -133 is a single-component, solvent evaporation curing butyl building waterproof sealant. Has excellent water resistance and anti-aging properties, concrete, metal, wood, stone and plastic surfaces have good adhesion. Mainly used to seal exterior wall frame and the wall between the windows and doors, as well as day side, the wall waterproof seal. Product Features 1, solvent evaporation curing, curing colloid whether or not, are not soluble in water 2, concrete, metal, wood, stone and steel surfaces have good adhesion 3, cured gel elasticity and flexibility 4, In the rainy season the construction progress of the project does not affect the main purpose sealing window frames and the wall between; waterproof rain awning with the seal between the wall; there is a large displacement of roof, wall joints of caulking and sealing; car compartment access sealing joints of. The main technical parameters of test items Q / (GK) AT 3 indicators measured sag vertical, mm ≤3 0 level without deformation without deformation extrusion resistance, ml / min ≥80 101 non-volatile matter, (wt)% ≥60 76.1 Density , g / ml 1.35 ± 0.1 1.45 dry time, min ≤180 15 peel adhesion, N / min ≥0.4 2.4 low temperature flexibility, ℃ -10 no crack compliant enterprise standard Q / ATHX 3-2008 building with butyl type a sealant construction methods, the need to prepare before sizing, bonding and sealing surfaces must be compact, solid, dry, clean and not contaminated with dust, low-intensity plaster, oil, water and so on. 2, when sizing the first incision beak cut to meet the requirements, along with wire or sharp object into his beak, cut the seal foil, into the glue gun, forced the closure of the pending squeeze glue directly. Note 1, the product is a solvent for rubber products, plastic colloid formation after evaporation of the solvent, there is a certain anti-displacement capacity. Mongolia has a surface moisture and dust can cause poor hydrocolloid adhesive, easy to sagging or cracking, but even after sizing by rainfall, seepage bubble, and no effect on the colloid. 2, when the ambient temperature is below 0 ℃, colloid will thicken. To facilitate the construction, within the first colloidal recommend preheating temperature no higher than 50 ℃ in the conservatory. 3. The construction of the thickness of not less than 5mm This product is appropriate sizing too thin or even fall off easily lead to cracking, about 12mm width sizing is appropriate. If the gap is too wide too deep, to ensure the quality of construction, require two or more sub-construction, and must ensure that the colloidal dense fill the entire gap, may be left empty. In addition, the thickness is preferably more than colloid has slits on both sides of the horizontal plane 2mm, and on both sides of the horizontal plane with each lap width of 2 ~ 3mm. 4, when sizing either convex curved surface, not the plastic surface to flatten, to prevent drying shrinkage cracking. This product within a week after sizing stable for solvent evaporation, should pay attention to a return visit to the local contraction caused cracking timely glue. 5, after the product glue yellow color will darken slightly, which is normal oily sealant will not affect other performance and quality of the glue. 6, the product will exist after the construction of about 20% of volume shrinkage, which is caused by solvent evaporation of the glue, please refer to the user to determine the sizing of this final strip thickness and thickness. Provide a complete product technical information technology services to customers. First-time users or large-scale use of the glue, construction feasibility tests must be done, that is the standard method to remove the plastic model parts to play in seven days observation. If the bottom of the strip firmly bonded, look no cracking off phenomenon, show that the glue can be used. Quality Assurance Our company passed the ISO9001 quality system demonstration, we are in strict accordance with the ISO9001 quality management system requirements to provide customers with high quality products. Curing, maintenance and repair one, Aetna -133 due to solvent evaporation and extrusion cured, dry time of about 30 minutes, completely cured adhesive is estimated to stabilize at a size 28 days after curing flexible rubber strips for lower body strength. 2, the initial sizing to be sealed to keep parts of the fixed and flat. Solvent cleaning and repair surface marked with the same color quality new sealant to repair. After non-toxic safety instructions for this product is fully cured. Uncured sealant Avoid contact with eyes and skin. Sealants during cure will release petroleum solvents, the construction should ensure good ventilation, to take protective measures when necessary. Do not use near fire source. Keep out of reach of children. Aetna -133 packaging with standard composite tube or plastic composite film packaging, the net capacity of 300ml. Aetna -133 color is black, white, gray or dark gray. Transportation and storage 1, the product is combustible goods, according to the normal way of transport. 2, the product must be stored in a cool dry place below 27 ℃, the shelf life of 12 months. A special statement, published in this article are believed to be reliable and factual information, but the actual situation (mainly construction conditions, use and adhesive materials) vary widely, so we can not guarantee that the products on certain uses and usage The applicability and accuracy. Before the selection of the product user should learn more about product characteristics, compliance with construction specifications and instructions to ensure the results are very necessary. If necessary, please contact our technical service personnel. 2, unless there is a written guarantee of Aetna, otherwise the company does not assume joint and several liability and losses due to improper selection FDA, improper construction, or caused by improper disposal, return or compensation is limited to static product itself.